radsecproxy
This section describes how to set up radsecproxy to act as a federation-level RADIUS and RADIUS/TLS server. It can then completely replace other RADIUS server products on the federation level.
More precisely, it will enable a server to:
- Accept requests from connected service providers via RADIUS and RADIUS/TLS.
- Forward requests to connected identity providers via RADIUS and RADIUS/TLS.
- Forward requests from international visitors to the European eduroam confederation root servers via RADIUS/TLS.
- Accept requests from the root servers via RADIUS/TLS for the own federation's users when they are roaming in another federation.
Version information
The prerequisites for this deployment are:
- radsecproxy version 1.6 or higher
- A server certificate and a private key for that certificate to establish the RADIUS/TLS connection which designates the server as an IdP+SP.
Include Page | ||||
---|---|---|---|---|
|
Sample config file
Most of the radsecproxy configuration file is static. This walk-through goes through the template radsecproxy.conf line by line and explains the meaning of each stanza.
Code Block |
---|
ListenUDP *:1812
ListenTCP *:2083
|
radsecproxy will receive requests from all connected Service Providers via both RADIUS and RadSec. Therefore it has to listen on the appropriate ports on its network interfaces (the * meaning: all interfaces). If you want radsecproxy to listen only on specific interfaces, enter the interface names here. Beware: in this case you may also have to set the more exotic options SourceUDP and/or SourceTCP (see the man page of radsecproxy for details).
Include Page | ||||
---|---|---|---|---|
|
Client definition
Code Block |
---|
client 127.0.0.1 {
type udp
secret testing123
}
client ::1 {
type udp
secret testing123
}
|
There is no other RADIUS server running on localhost, which makes these client definitions almost superfluous. They may be of some use however to initiate debugging requests and tests from the server itself, so it is considered good practice to list localhost as a client. If your system is not IPv6-enabled, simply delete the second stanza.
Code Block |
---|
client __SP_IP_ADDR__ {
type udp
secret __SP_SECRET__
FTicksVISCOUNTRY XZ # will generate F-Ticks for a non-existant visited country
}
|
Stanzas like this one are used for each connected service provider that is connected via RADIUS. You need to know the IP address of every SP's RADIUS server and negotiate a shared secret with the SP
Please note that the client and server stanza for the GEANT Monitoring (SA3-T2 activity) have the same host address, but different stanza names. This is important: it disables the LoopDetection for this host, and the SA3 monitoring deliberate uses loops to do its tests. The following stanza is the eduroam Service Activity's monitoring client. Negotiate the IP address and shared secret for European monitoring with the operators in SA3-T2 (eduroam Operational Team) and enter it here.
Code Block |
---|
client SA3-monitoring-incoming {
host x.y.z.a
type UDP
secret __MONITORING_SECRET__
}
|
.
Code Block |
---|
client incoming {
host 0.0.0.0/0
host [::]/0
type |
Wiki Markup |
h2. radsecproxy This section describes how to set up radsecproxy to act as a federation-level RADIUS+RadSec server. It can then completely replace other RADIUS server products on the federation level. More precisely, it will enable a server to: * Accept requests from connected service providers via RADIUS and RadSec. * Forward requests to connected identity providers via RADIUS and RadSec. * Forward requests from international visitors to the European eduroam confederation root servers via RadSec. * Accept requests from the root servers via RadSec for the own federation's users when they are roaming in another federation. * [Base configuration / logging / F-Ticks|display/H2eduroam/How+to+deploy+eduroam+at+national+level#Howtodeployeduroamatnationallevel-Baseconfiguration%2Flogging%2FFTicks] * [Client definition|display/H2eduroam/How+to+deploy+eduroam+at+national+level#Howtodeployeduroamatnationallevel-Clientdefinition] * [Request forwarding|display/H2eduroam/How+to+deploy+eduroam+at+national+level#Howtodeployeduroamatnationallevel-Requestforwarding] * [Caveats|display/H2eduroam/How+to+deploy+eduroam+at+national+level#Howtodeployeduroamatnationallevel-Caveats] h3. Version information The prerequisites for this deployment are: * radsecproxy version 1.4.2 or higher * A server certificate and a private key for that certificate to establish the RadSec connection which designates the server as an IdP+SP. h3. Installation On UNIX-like systems, the installation is very simple: # Download the code from [http://software.uninett.no/radsecproxy/]. # Unpack the code. # Navigate into the unpacked directory (the base directory) and type: _make_ The code is ISO C and should compile cleanly. It usually does not require a ./configure. 4. After compiling, the executable {code} radsecproxy {code} is in the base directory. Either run this executable here or copy it to a convenient location (e.g. /usr/local/bin) and run it there. Execution does not require root rights. 5. Copy the template configuration file below into {code} /etc/radsecproxy.conf {code} 6. Create the directory _/etc/radsecproxy.d/certs/ca/_. The template configuration file requires this directory to contain the accredited CA root certificates and the corresponding Certificate Revocation Lists (CRLs) in their OpenSSL hash form. See the section xyz for information about the CA download. 7. Fill the lines marked with __STUFF__ with the required information as explained below. 8. Start radsecproxy and enjoy (for first-time use, starting it with the \--f option is recommended, it will start radsecproxy in the foreground and show some verbose startup messages).\\ h3. h3. Sample config file Most of the radsecproxy configuration file is static. Therefore, a template configuration file is provided at [http://www.eduroam.org/downloads/docs/eduroam-cookbook-scripts.zip|http://www.eduroam.org/downloads/docs/eduroam-cookbook-scripts.zip]. A detailed explanation of this configuration file follows. However, the comments included in the file should make its action almost self\- explanatory. This means you can start and experiment with it right after installation. h3. Base configuration / logging / F-Ticks This walk-through goes through the template radsecproxy.conf line by line and explains the meaning of each stanza. {code} ListenUDP *:1812TLS ListenTCP tls *:2083 {code} radsecproxy will receive requests from all connected Service Providers via both RADIUS and RadSec. Therefore it has to listen on the appropriate portsdefaultClient on its network interfaces (the * meaning: all interfaces). If you want radsecproxy to listen only on specific interfaces, enter the interface names here. Beware: in this case you may also have to set the more exotic options SourceUDP and/or SourceTCP (see the man page of radsecproxy for details). {code} LogLevel 3 LogDestination x-syslog:///LOG_LOCAL0 {code} A logging level of 3 is the default and recommended log level. Radsecproxy will then log successful and failed authentications on one line each. The log destination is the local syslog destination. {code} LoopPrevention On {code} This enables a semi-automatic prevention of routing loops for RADIUS connections. If you define a client {...\] and a server {...} (see below) and give them the same descriptive name, the proxy will prevent proxying from the client to that same server. {code} tls default { CACertificatePath secret radsec } |
After all specific clients in the configuration, you can the above stanza as a "catch-all" for incoming RADIUS/TLS connections.It does not need to be modified (if you do not support IPv6, you can delete the second "host" line though). In particular, the string "radsec" for secret is fixed by the RADIUS/TLS protocol and is required to remain unchanged. It also has no effect; RADIUS/TLS depends on TLS security rather than the shared RADIUS secret.
The eduroam trust model requires that a SP that tries to connect has:
- A X.509 certificate from an eduroam-accredited CA
- which carries a Policy OID as configured above to prove authorisation as a eduroam Service Provider
These checks were defined via "tls defaultClient", above.
Request forwarding
To deliver requests to your connected IdPs, their servers need to be configured. This stanza is for IdP servers using RADIUS.
Code Block |
---|
server __DESCRIPTIVE_NAME_ {
host __IP_ADDR__
type UDP
secret __SERVER_SECRET__
}
|
This is the equivalent stanza for IdP servers using RADIUS/TLS.
Code Block |
---|
server __RADSEC_PEER_DNS_NAME_ {
type TLS
tls defaultServer
secret radsec
statusserver on
}
|
The two following stanzas define the uplink to the European eduroam Confederation root servers. This entry can be kept as it stands and doesn't need any further configuration.
Code Block |
---|
server etlr1.eduroam.org { type /etc/radsecproxy/certs/ca/ CertificateFile TLS tls /etc/radsecproxy/certs/CERT_PEM__ CertificateKeyFile defaultServer /etc/radsecproxy/certs/CERT_KEY__ CertificateKeyPasswordsecret __CERT_PASS__ # radsec CRLCheck statusserver on } server etlr2.eduroam.org { On } {code} This section defines which TLS certificates should be used by default. This installation of radsecproxy always uses the same certificates, so this is the only TLS section. CACertificatePath contains the eduroam-accredited CA certificates with filenames in the OpenSSL hash form. The parameters below need to be adapted to point to your server certificate in PEM format, the private key for this certificate and the password for this private key if needed, respectively. If no password is needed for the private key, you can comment this line (precede it with a # sign). The option CRLCheck validates certificates against the Certificate Revocation List (CRL) of the CAs. It requires a valid CRL in place, or else the certificate validation will fail. Therefore, it is important to regularly update the CRLs by re-downloading them as described above. _rewrite defaultclient {_ _ removeAttribute 64_ _ removeAttribute 65_ _ removeAttribute 81_ _}_ This section deletes attributes from RADIUS requests that convey VLAN assignment information. If VLAN information is sent inadvertently, it can cause a degraded or non-existent service for the end user because he might be put into the wrong VLAN. Connected service providers should filter this attribute on their own. Connected Identity Providers should not send this attribute at all. Checking for the existence of these attributes on the federation server is just an optional additional safety layer. If you do have a roaming use for cross\- institution VLAN assignment, you may want to delete this stanza. _client 127.0.0.1 {_ _ type udp_ _ secret testing123_ _}_ _client ::1 {_ _ type udp_ _ secret testing123_ _}_ There is no other RADIUS server running on localhost, which makes these client definitions almost superfluous. They may be of some use however to initiate debugging requests and tests from the server itself, so it is considered good practice to list localhost as a client. If your system is not IPv6-enabled, simply delete the stanza about client ::1. _client \__SP_IP_ADDR__ {\__ type UDP{_}_ secret \__SP_SECRET_\_\__}_ Stanzas like this one are used for each connected service provider that is connected via RADIUS. You need to know the IP address of every SP's RADIUS server and negotiate a shared secret with the SP. _client incoming {_ _ host *_ _ type TLS_ _ secret mysecret_ _ matchcertificateattribute_ \_SubjectAltName:URI:/\^[https://registry.edugain.org/resolver?urn=urn:geant:eduroam:\_|https://registry.edugain.org/resolver\?urn=urn:geant:eduroam:_] _component:(sp\|proxy\|confederation-root).*$/_ _}_ All incoming RadSec connections can be handled with this stanza. It does not need to be modified. The eduroam trust model requires that a SP that tries to connect has: * A X.509 certificate from an eduroam-accredited CA (configured above in block *tls default*). * A URN proving its eligibility (this is achieved with the matchcertificateattribute option). The traditional RADIUS *shared secret* has no meaning in RadSec and can be statically set without security implications. In current eduroam deployments, it is set to *mysecret*. This may change in the future. Please note that the client and server stanza for the Service Activity 5 (SA5) monitoring have the same host address, but different stanza names. This is important: it disables the LoopDetection for this host, and the SA5 monitoring deliberate uses loops to do its tests. _client SA5-monitoring-incoming {_ _ host 161.53.2.204_ _ type UDP_ _ secret \__MONITORING_SECRET_\_\_ _}_ This is the eduroam Service Activity's monitoring client. Negotiate a shared secret for monitoring with the operators in SA5 and enter it here. _server \__DESCRIPTIVE_NAME__ {\__ host \__IP_ADDR_\_\__ type UDP{_}_ secret \__SERVER_SECRET_\_\__}_ To deliver requests to your connected IdPs, their servers need to be configured. This stanza is for IdP servers using RADIUS. _server \__RADSEC_PEER_DNS_NAME__ {\__ type TLS{_}_ secret mysecret{_}_ statusserver on{_}_ matchcertificateattribute_\_SubjectAltName:URI:/\^[https://registry.edugain.org/resolver?urn=urn:geant:eduroam:\_|https://registry.edugain.org/resolver?urn=urn:geant:eduroam:_]_component:(idp\|proxy\|confederation-root):.*$/i{_}_}_ This is the equivalent stanza for IdP servers using RadSec. _server etlr1.eduroam.org {_ _ type TLS_ _ secret mysecret_ _ statusserver on_ \_ matchcertificateattribute _ \_SubjectAltName:URI:/\^[https://registry.edugain.org/resolver?urn=urn:geant:eduroam:component:confederation-root:Europe:ETLR:.*$/i\_|https://registry.edugain.org/resolver\?urn=urn:geant:eduroam:component:confederation-root:Europe:ETLR:.*$/i_] _}_ _server etlr2.eduroam.org {_ _ type TLS_ _ secret mysecret _ _ statusserver on_ \_ matchcertificateattribute _ \_SubjectAltName:URI:/\^[https://registry.edugain.org/resolver?urn=urn:geant:eduroam:component:confederation-root:Europe:ETLR:.*$/i\_|https://registry.edugain.org/resolver\?urn=urn:geant:eduroam:component:confederation-root:Europe:ETLR:.*$/i_] _}_ These are the European eduroam Confederation root servers. This entry can be kept as it stands and doesn't need any further configuration. _server SA5-monitoring-outgoing {_ _ host 161.53.2.204_ _ type UDP_ _ secret \__MONITORING_SECRET_\_\_ _}_ _server TODO:add SRCE RadSec server here {_ _ type TLS_ _ secret mysecret_ _ statusserver on_ \_ matchcertificateattribute _ _SubjectAltName:URI:/^urn:geant:eduroam:component:confederation-root:Europe:Monitoring:.*/i_ _}_ SA5 monitoring works both ways. The client entry near the beginning of the configuration file was needed for incoming requests from the monitoring servers. The two entries here specify the outgoing connections to the monitoring servers. Outgoing connections can use either RADIUS (first entry) or RadSec (second entry) at your discretion. You can configure both, and select the preferred way later in the special monitoring realm *eduroam.TLD*. Finally, the IdP realms need to be defined. This is done in the remainder of the configuration file: _realm /myabc\.com$ {_ _ replymessage "Misconfigured client: default realm of Intel PRO/Wireless supplicant\! Rejected by <TLD>."_ _}_ \_realm /^\[radsecproxy-flr^@\]*$ { replymessage "Misconfigured client: empty realm! Rejected by <TLD>."__}_ There are some known client-side misconfigurations. If they were not already caught by the SP local RADIUS server, it does not make sense for the proxy to send these requests up to the eduroam infrastructure. These requests are immediately rejected. *Note:* if you need to blacklist an existing realm for some reason, you can follow the myabc.com example, copying and replacing it with the realm to be blacklisted. _realm /_{_}IDP_REALM{_}_$ {_ _ server \__FROM_SERVER_STANZAS_ABOVE_\_\_ _ server \__BACKUP_NAME_\_\_ _}_ Requests that are coming in from upstream and are supposed to be handled by an identity provider are listed in stanzas like this. __IDP_REALM__ contains the realm of the connected IdP. Create one such stanza for each IdP realm. If an IdP has multiple servers for a failover configuration, you can list all servers in a row, as in the example above. _realm /eduroam\._{_}YOUR_TLD__ {\__ server SA5-monitoring-outgoing{_}_ server TODO:SRCE RadSec server{_}_}_ The configuration stanza above is for outgoing SA5 monitoring connections. You can select your preference for RADIUS or RadSec for the outgoing connections by changing the order of the server stanzas. _realm /\._{_}YOUR_TLD{_}_$ {_ _ replymessage "Misconfigured supplicant or downstream server: uses known\- bad realm in <TLD> federation\!"_ _}_ All the valid realms were listed earlier in the configuration file, and this server is authoritative for the own TLD. If a supplicant or downstream servers sends a realm with the own TLD, but also with a realm name that is not registered, this request is unauthorised and bound to fail. It will be rejected immediately to prevent routing loops. _realm \* {_ _ server etlr1.eduroam.org_ _ server etlr2.eduroam.org_ _}_ Finally, all realms that do not belong to the own federation are forwarded to the European eduroam Confederation root servers.type TLS tls defaultServer secret radsec statusserver on } |
European monitoring works both ways. The client entry near the beginning of the configuration file was needed for incoming requests from the monitoring servers. The entry below specifies the outgoing connections to the monitoring server. Outgoing connections are currently monitored with RADIUS only. Use the negotiated IP address and shared secret with SA3-T2 Monitoring in the following stanza:
Code Block |
---|
server SA3-monitoring-outgoing {
host a.b.c.d
type UDP
secret __MONITORING_SECRET__
}
|
After defining the server configurations, we need to define which RADIUS realms are going to be forwarded to which server(s). This is done in the remainder of the configuration file.
First, there are (very few) known-bad realms which are not forwarded at all. They should ideally never reach the FLR server, and be caught by the SP local RADIUS server, but as an extra safety measure they are filtered (i.e. immediately rejected) here:
Code Block |
---|
realm /myabc\.com$/ {
replymessage "Misconfigured client: default realm of Intel PRO/Wireless supplicant! Rejected by <TLD>."
accountingresponse on
}
realm /@.*3gppnetwork\.org$/ {
replymessage "Misconfigured client: Unsupported 3G EAP-SIM client!"
accountingresponse on
}
realm /^$/ {
replymessage "Misconfigured client: empty realm! Rejected by <TLD>."
accountingresponse on
}
|
Note: if you need to blacklist an existing realm for some reason, you can follow the myabc.com example, copying and replacing it with the realm to be blacklisted.
Requests for proper realms that are coming in from upstream and are supposed to be handled by an identity provider are listed in stanzas like the below. _IDP_REALM_ contains the realm of the connected IdP. Create one such stanza for each IdP realm. If an IdP has multiple servers for a failover configuration, you can list all servers in a row, as in the example below.
Code Block |
---|
realm /IDP_REALM$/ {
server __FROM_SERVER_STANZAS_ABOVE__
server __BACKUP_NAME__
}
|
The configuration stanza below is for outgoing European monitoring connections.
Code Block |
---|
realm /eduroam\.YOUR_TLD/ {
server SA3-monitoring-outgoing
}
|
All the valid realms were listed earlier in the configuration file, and this server is authoritative for the own TLD. If a supplicant or downstream servers sends a realm with the own TLD, but also with a realm name that is not registered, this request is unauthorised and bound to fail. It will be rejected immediately to prevent routing loops.
Code Block |
---|
realm /\.YOUR_TLD$/ {
replymessage "Misconfigured supplicant or downstream server: uses known-bad realm in <TLD> federation!"
}
|
Finally, all realms that do not belong to the own federation are forwarded to the European eduroam Confederation root servers. However, we limit this to 'sane' realms: these must include a tld of at least 2 characters. Anything else is dropped.
Code Block |
---|
realm /@.+\..{2,}$/ {
server etlr1.eduroam.org
server etlr2.eduroam.org
}
realm * {
replymessage "Misconfigured client: username does not contain a valid realm!"
} |
Goodies
This section contains some optional configuration parameters that can do good in many cases.
Keeping the config file at a manageable size
radsecproxy allows to split the configuration file into several files on disk and include the parts into the main configuration file. This is very practical when many sites have to be managed. You can create a subdir and put the client, server, realm parts together in one file per participant. By adding
Code Block |
---|
include /etc/radsecproxy.conf.d/*.conf
|
into the main config file, you can put all the participant files into that directory.